1. Collection of all required technical data from client or suppliers

2. Understanding the specific requirements from client and LEED.

3. Calculation of Load Schedule

4. Designing of Lighting Distribution Systems

5. Designing of Power Distribution Systems

6. Designing of Fire Protection Systems

7. HVAC Electrical distribution Design

8. Lift Electrical Specification

9. Single Line Diagram

10. Cable Sizing & Tray Design

11. Transformer Selection

12. Panel Board (MDB, SMDB, SDB) Selection

13. Capacitor Bank Selection

14. Bus Bar Selection

15. UPS & Generators Selection

16. Emergency Lighting

17. Conduit Design

18. Earthing Layout

19. Selection of Solar Panel, Solar Battery, Solar Regulators

20. Bill of Quantity, Estimation & Costing of a Project

21. Shop/As Build Drawings

22. Schematic, Section, Isometric, Schedule Drawings Understanding the specific requirements from client and LEED.

23. Authority drawing plan. (Client or Supplier will take the responsibility of approval of the drawing from any authority/Compliance).

1. Collection of all required technical data from client or supplier.

2. Understanding the specific requirements from client and LEED.

3. Fire Detection System Design

4. Fire Sprinkler System Design

5. Fire Monitoring Station Design

6. Fire Extinguisher CO2, ABC & Chemical Powder Design

7. Fire Pump Specification

8. Sprinkler Pipe Design

9. Fire Hose Reel & Cabinet Design

10. Fire Hydrant Pipe Design

11. Fire Equipment Design & Selection

12. Hydraulic Calculation

13. Bill of Quantity, Estimation & Costing of a Project

14. Shop/As Build Drawings

15. Schematic, Section, Isometric, Schedule Drawings

16. Authority drawing plan. (Client or Supplier will take the responsibility of approval of the drawing from any authority/Compliance).

1. Collection of all required technical data from client or supplier.
2. Understanding the specific requirements from client and LEED.
3. Lightning Protection System Design.
4. Standard BOQ for LPS System.
5. Earthing Design
6. Earth Pit Design
7. Bill of Quantity, Estimation & Costing of a Project
8. Shop Drawings
9. Schematic, Section, Isometric, Schedule Drawings
10. Sump Design
11. Authority drawing plan. (Client or Supplier will take the responsibility of approval of the drawing from any authority/Compliance).

1. Collection of all required technical data from client or supplier.

2. Understanding the specific requirements from client and LEED.

3. Sump Design

4. Overhead Tank Design

5. Storm Water Drainage Design

6. Pumping Main Pipe Design

7. Drainage Water Pipe Design

8. Pump Room Design

9. Manhole Design

10. Water Treatment Plant Design

11. Sewerage Treatment Plant Design

12. Hydraulic Calculations for Pump Selection

13. Auto Pneumatic System

14. Pressure Tank Sizing

15. Septic Tanks, Soak Away Pits, Dispersion Trenches.

16. Garden & Fountain Water Pipe Sizing

17. Hot Water Estimation, Heater Capacity Selection

18. Equipment Selection & its Accessories

19. Bill of Quantity, Estimation & Costing of a Project

20. Shop/As Build Drawings

21. Schematic, Section, Isometric, Schedule Drawings.

22. Authority drawing plan. (Client or Supplier will take the responsibility of approval of the drawing from any authority/Compliance).

1. Collection of all required technical data from client or supplier.

2. Understanding the specific requirements from client and LEED.

3. Mechanical Ventilation System design for General areas.

4. Air Cooling System design for offices

5. HVAC Duct Design

6. Chilled Water & Cooling Tower Pipe Design

7. Package AC, DX Units, Split AC Design

8. AHU & Pump Room Design

9. Ventilation Designing – Toilet, Kitchen, Car Parking

10. Expansion Tank Design

11. Stair Well Pressurization System Design

12. Refrigerant Pipe Sizing for DX Systems

13. ESP Calculations for Blower Fan Selection

14. Bill of Quantity, Estimation & Costing of a Project

15. Shop Drawings

16. Schematic, Section, Isometric, Schedule Drawings Sump Design

17. Authority drawing plan. (Client or Supplier will take the responsibility of approval of the drawing from any authority/Compliance).

1. CCTV Surveillance System in this project comply With Integrated Security System.

2. Bill of Quantity, Estimation & Costing of a Project

3. Shop Drawings

4. Schematic, Section, Isometric, Schedule Drawings

5. Authority drawing plan. (Client or Supplier will take the responsibility of approval of the drawing from any authority).

6. Authority drawing plan. (Client or Supplier will take the responsibility of approval of the drawing from any authority/Compliance).

1. AutoCAD (Electrical, Plumbing, Fire & HVAC) – 4 Weeks

2. AutoCAD p&id software – 2 Weeks

3. AutoCAD Fusion 360 software – 2 Weeks

4. CFD: Computational Fluid Dynamics – 2 Weeks

5. CYPE software (Electrical, Plumbing, Fire, HVAC & Structure) – 3 Weeks

6. Light Simulation (CYPE Software & DIALux) – 2 Weeks